Pebble Steel Troubleshooting

Display Looks Torn

The sieve displays dead pixels, tearing, distortions, or artifacts .
first, try performing a factory reset. choose Settings from the main menu, and Factory Settings is the last option .
If this does not work, submerge your pebble steel in warm ( not boiling hot ) urine for 5 minutes. After removing from the warm water, let the pebble Steel baby-sit for 1 minute before submerging it in cold water for 5 minutes.

Pebble Steel is Alerting for Old Notifications/Not Alerting for New Notifications

The pebble Steel is either vibrating repeatedly for an old telling or not vibrating for a new presentment .

Restart Pebble Steel

If your pebble Steel is vibrating multiple times for an old telling, try restarting the pebble Steel by holding down the bet on and choose buttons simultaneously for about 10 seconds. Send a trial Ping from the Pebble app to see if the Pebble Steel vibrates. If it distillery does n’t vibrate, contact the support system about the problem and include the information that pebble requires .

Notification Settings are Turned Off

If your pebble Steel is not vibrating to alert a fresh telling, make sure the settings for the vibrations are by rights configured. From the Menu, go to Settings and then Notifications. Make sure that the vibration choice is enabled .
If this does n’t work, the oscillation device may need to be replaced. Replace the vibration device using this usher .

Buttons Are Unresponsive/Active When Unprompted

One or more of your pebble Steel ’ sulfur buttons are either failing to function or are not responding when pressed .

Recalibrate Pebble Steel

If any of your pebble Steel ’ randomness buttons are not functioning correctly, and you have already performed a factory reset with no success ( if able to do so ), submerge the pebble Steel under warm water for a few moments. then, remove the watch from the water and hard crush and hold each button ( individually ) for 7 seconds .
If this does not work, you can replace the buttons using this guide .

Adjust Watch Band

If the buttons are besides responsive, try adjusting the wear of the Pebble Steel on your wrist. If the watch band is besides lax it will be more probable to slide around and cause undesirable button stimulation, so try tightening the band. besides, see if changing the position of the pebble Steel to a higher or a lower location on your arm fix this issue .

Notification Issues With iOS Devices

The pebble Steel is either not receiving notifications or receiving twin notifications .

Enable ‘Show Notifications’ Setting

If your pebble Steel is not welcome notifications, make sure that the ‘Show Notifications ‘ choice on your iPhone is enabled. This is found under Settings to Bluetooth. Your pebble sword should be connected and ‘Show Notifications ‘ turned on .

Delete Old Notifications

For iPhone owners who are receiving duplicate notifications, pull down the condition stripe at the top of the iPhone display and erase old notifications. You should besides be able to hit the Select button on your pebble sword to clear the notifications as they pop up .

Device Not Charging/Turning On

Your pebble Steel will not office on or connect properly to the charger .

Charge Pebble Steel Completely

If your pebble Steel will not turn on after completely depleting the barrage, it may take about three hours to amply recharge again .
If your pebble steel will hush not turn on, make indisputable the device is plugged in by rights and drawing ability. Make sure the USB end of the charging cable is plugged in before attaching the early conclusion to the pebble Steel. Try multiple ports and outlets to determine if the topic is with the pebble Steel or with the charging cable itself. You may have to replace the charging cable.

Clean the Charging Cable

If your pebble sword does not connect properly to the charging cable, try cleaning the alloy connection surface. There are four alloy contact points on the charging helping of the pebble Steel. These are cleaned with 90 % rubbing alcohol .
There are besides four spring-loaded pins on the charging cable. These are cleaned by rubbing a pencil eraser along the surface. Make certain that all four pins depress smoothly and return to the lapp outward position.

generator : https://enrolldetroit.org
Category : Social

Trả lời

Email của bạn sẽ không được hiển thị công khai.