Step 1: Get the right equipment
You ’ re going to need an iron. preferably the cast-iron lets you pour water in ( for steam ), and better even it has one of those slippery teflon coated bottoms. If the iron can ’ metric ton spray water system out the front man you will want a alter bottle of some type that can spray a fine mist. You ’ ll besides need an ironing board. If you ’ re in New York, you have a small ironing circuit board you can set on your dinky fiddling boom room table. If you live in California, you ’ re wondering what an ironing control panel is because you wear nothing but t-shirts. If you live anywhere else, you have a nice big fold out ironing board you can setup in your be room. Whatever works !
Step 2: Get set up
Setup your ironing board in a comfortable invest where you ’ ll be able to spread the shirt out without wrinkling it all over again. If you ’ re planning to iron several shirts in a quarrel make sure you can see the television from this angle. Plug the cast-iron in and turn the dial to point to “ cotton ” or whatever the hottest put is .
Step 3: Iron the back of the shirt
We advocate starting with the back of the shirt because this is going to get wrinkled ampere soon as you put it on and sit down anyways. Unbutton the shirt completely, and spread it out over the ironing board. Put the apparel shirt on the board so that the narrow end of the dining table is going into the back of the shoulder of the shirt and the edge of the ironing board is along the side of the shirt. With tone down pressure, slide the iron down the shirt top to bottom, being careful that you keep the shirt flat and don ’ thyroxine actually iron wrinkles into the garment. Use a little steam or spray some urine on any wrinkles that aren ’ t going away easily. Once you ’ ve done one side of the back, slide the shirt over and do the other side barely the lapp.
Step 4: Iron the sleeves
Iron the sleeves ( one at a time ). Lay the sleeve long ways on the ironing control panel and carefully flatten the sleeve with your hands such that it folds along the hem on the bottom of the sleeve. Starting from around the arm scar area, iron toward the cuff and away from the bottom hem. It ’ mho optional to iron in a graze on the top of the sleeve, but if you do this kris should be straight. If you don ’ deoxythymidine monophosphate want a graze, just iron close to the top but not over it. Repeat on the other sleeve .
Step 5: Iron the top part of the shirt front and yoke
This is the most crafty function to get right but besides the most visible since it ’ s right up by your neck and fountainhead. For this area you ’ re going to want to use the minute pointy english of the ironing display panel. Pull one shoulder of the shirt over this part of the ironing board such that you have a well-defined view of one side of the yoke and the front of the shirt just below the yoke. The collar should be sticking up straight and curving around in a circle. spray this area down to be dampen and iron cautiously around the crook of the collar .
Step 6: Iron the collar
now we do the collar. Take out the obliterable collar stays from the shirt collar ( wear ’ deoxythymidine monophosphate lose them ). Button down collars won ’ t have collar stays, but you ’ ll want to unbutton the small buttons that hold the collar down. Unfold the collar so that it is “ pop ” and lay it flat on the ironing control panel with the back facing up. Spray the collar down with a effective total of water and give it ~30 seconds to soak in. Iron from the center of the apprehension outwards all the way to the tips of the collar points. Because the collar is a chummy, stiffer patch of material you may need to press slightly harder than you would for the rest of the shirt. When you ’ re done, put the collar stays back in the collar and fold the collar down again. If you want you can besides fold the collar down and iron in a bite of a kris at the battlefront of the collar so that it will angle down sharply. You won ’ t be able to iron this kris all the way around since the collar is designed to curve, but a little act of a kris at the front can make things look a act sharp.
Step 7: Iron the shirt front
last, do the movement of the shirt. Hopefully, by now you ’ ve got the hang of it. Do one side at a time. Be careful of the buttons. Make sure the front placket is not folded over in a way it shouldn ’ thyroxine be. Use the point of the iron to get in the areas up around the movement of the collar. If the dress shirt has a pouch, this can be catchy. You can be crafty. As you push the iron down on one side you can pull gently on the other to keep things close and straight .